The phone deletes the oldest entry when the log is full to make room for new calls. Page Memory Match Caller ID Caller ID history Memory match If the incoming telephone number exactly matches a telephone number in your directory, the name that appears on the screen matches the corresponding name in your directory. For example, if Christine Smith calls, her name appears as Chris Chris if this is how you entered it into your directory. When a handset is in idle mode, press qCID to review the caller ID history in reverse chronological order starting with the most recent call.
Battery status - low battery flashing ; place handset in telephone base or charger to recharge. You are trying to reach an empty caller ID history. To register a new handset, see page You might need to charge the new handsets before registering to the telephone base, refer to the table on page 7 for charging time. You may need to de-register your handsets if: You have twelve registered handsets and need to replace a handset.
Page Appendix D Troubleshooting Appendix D Troubleshooting If you have difficulty with your phone, please try the suggestions below. For www. Page 48 Appendix D Troubleshooting I cannot dial out. The cordless handset might take a second or two to find the telephone base and produce a dial tone.
This is normal. You might have moved out of range. Unplug the electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset. Try installing your phone as far away from the following electronic devices as possible: television sets, VCRs, or other cordless telephones. For optimum daily performance, return the cordless handset to the telephone base or charger when not in use.
If this does not solve the problem, re-locate your phone or modem farther apart from one another, or use a different surge protector. Caller ID when on a call. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock. Telephone calls are transmitted between the telephone base and the handset by radio waves, so there is a possibility that your cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset.
This identifier must be provided to your local telephone company upon request. Page 58 Appendix G FCC part 68 and ACTA Industry Canada Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference, including interference that may cause undesired operation.
Manuals and Videos Please enter your model number in the box below to find the manual and quick start guide. Model number: Turn over the base of your phone to locate the model number as illustrated in the image below. All rights reserved. Error message. This site uses cookies to store information on your computer. Your product may be shipped with a protective sticker covering the handset or telephone base display - remove it before use. For customer service or product information, visit our website at www.
In Canada, dial 1 Plug the power adapter into an electrical outlet not controlled by a wall switch. The power adapter is intended to be correctly oriented in a vertical or floor mount position.
The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Install the battery as shown below. After installing the battery, you can make and receive short calls. Place the handset in the telephone base or charger when not in use. For optimal performance, charge the handset battery for at least 16 hours. Charge the handset by placing it face up in the charger. Use only the supplied rechargeable battery or replacement battery model BT To order, visit our website at.
If you do not use the handset for a long time, disconnect and remove the battery to prevent possible leakage. Welcome to ManualMachine. We have sent a verification link to to complete your registration. If you want to change to wall-mounting installation, see page 9 for details. Plug the small end of the power adapter into the power jack on the bottom of the telephone base.
Plug the large end of the power adapter. Route the power adapter cord through the slot. Plug one end of the telephone line cord into the telephone jack on the bottom of the telephone base. Place the cords into the channels. Plug the other end of the telephone line. Use only the power adapter s supplied with this product. To order a replacement power adapter, visit our website at www.
The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Plug the power adapter into an electrical outlet not controlled by a wall switch. Install the battery as shown on the next page. Once you have installed the battery, the screen indicates the battery status see table below.
If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the charger when not in use.
See the table on page 58 for battery operating times. If the screen is blank, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. The following table summarizes the battery charge indicators and actions to take. NOTE: If you are on a phone call in low battery mode, you hear four short beeps every minute. Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label.
Align the cover flat against the battery compartment, then slide it upwards until it clicks into place. Charge the handset by placing it face forward in the telephone base or charger. Use only the supplied rechargeable battery or replacement battery model BT To order, visit our website at www.
If you do not use the handset for a long time, disconnect and remove the battery to prevent possible leakage. Your telephone base is ready for tabletop use. If you want to mount your telephone on a wall, use the provided wall-mount bracket to connect with a standard dual-stud telephone wall-mounting plate. If you do not have this mounting plate, you can purchase one from many hardware or consumer. You might need a professional to install the mounting plate. Position the telephone base as shown below.
Insert the extended tabs marked A of the wall-mount bracket into the slots on the back of the telephone base marked A. Push the telephone base down until it is securely in place.
If you are using a DSL filter, plug the line cord into the filter now. Route the telephone line cord or DSL filter through the wall-mount bracket hole. Route the power cord out of the bottom of the telephone.
Plug the telephone line cord or DSL filter into the wall jack. Plug the power adapter into a power outlet not controlled by a wall switch.
Align the holes on the wall-mount bracket with the standard wall plate and slide the wall-mount bracket down until it locks securely. Bundle the telephone line cord and power adapter cord neatly with a twist tie. If the telephone line cord and power adapter cord are bundled, untie them first. Push the telephone base up to detach it from the wall-mount bracket.
0コメント